In today's podcast episode, Jonathan Romberg comes on to discuss how the Danfoss ERC 213 works and reviews its parameters with us.
Timestamps: 10:30 \u2013 Key Features10:41 \u2013 Voltage Protection
10:56 \u2013 Compressor Protection
14:43 \u2013 Applications15:15 \u2013 App 0 No predefined application
15:28 \u2013 App 1 Medium temperature ventilated refrigeration units with timed natural defrost
15:52 \u2013 App 2 Medium temperature ventilated refrigeration units with timed electrical defrost
16:03 \u2013 App 3 Low temperature ventilated refrigeration units with timed electrical defrost
16:13 \u2013 App 4 Medium temperature ventilated refrigeration units with electrical defrost (by temperature)
16:26 \u2013 App 5 Low temperature ventilated refrigeration units with electrical defrost (by temperature)
16:37 \u2013 App 6 No predefined application with a simplified list of parameters
19:45 \u2013 Sensors 22:06 \u2013 Basic Groups of Parameters 23:09 \u2013 r-- Thermostat23:12 \u2013 r00 Temperature setpoint
23:24 \u2013 r01 Differential
23:32 \u2013 r02 Min setpoint limitation and r03 Max setpoint limitation
24:02 \u2013 r04 Display offset
25:19 \u2013 r05 Display Unit (\xb0C/\xb0F)
25:33 \u2013 r09 Calibration of Sair
25:47 \u2013 r12 Main switch
27:17 \u2013 r13 Night set back
27:48 \u2013 r40 Thermostat reference displacement (offset temperature)
28:30 \u2013 r96 Pull-down duration and r97 Pull-down limit temperature
29:06 \u2013 A-- Alarms29:13 \u2013 A03 Delay for temperature alarm during normal conditions
30:15 \u2013 A12 Delay for temperature alarm during pull-down/start-up/defrost
31:00 \u2013 A13 High-temperature alarm limit (Cabinet/Room)
31:34 \u2013 A14 Low-temperature alarm limit
31:55 \u2013 A27 DI1 delay and A28 DI2 delay
32:17 \u2013 A37 Condenser high alarm limit
32:41 \u2013 A54 Condenser high block limit
33:45 \u2013 A72 Voltage protection enable
34:03 \u2013 A73 Minimum cut-in voltage and A74 Minimum cut-out voltage
35:04 \u2013 A75 Maximum Voltage
37:37 \u2013 d-- Defrost37:49 \u2013 d01 Defrost method
38:32 \u2013 d02 Defrost stop temperature
38:50 \u2013 d10 Defrost stop sensor
40:51 \u2013 d03 Defrost interval
41:16 \u2013 d04 Max defrost time
43:38 \u2013 d05 Defrost delay at power up (or DI signal)
44:29 \u2013 d06 Drip delay
44:49 \u2013 d07 Fan delay after defrost
45:49 \u2013 d08 Fan start temperature after defrost
47:21 \u2013 d09 Fan during defrost
47:40 \u2013 d10 Defrost stop sensor (part II)
48:16 \u2013 d18 Compressor accumulated runtime to start defrost
50:04 \u2013 d19 Defrost on demand
53:26 \u2013 d30 Defrost delay after pull-down
53:53 \u2013 F-- Fan control54:03 \u2013 F01 Fan at compressor cutout
55:00 \u2013 F04 Fan stop evaporator temperature
55:51 \u2013 F07 Fan ON cycle and F08 Fan OFF cycle
56:28 \u2013 c-- Compressor56:37 \u2013 c01 Compressor minimum ON time
56:47 \u2013 c02 Compressor minimum OFF time
57:01 \u2013 c04 Compressor OFF delay at door open
57:51 \u2013 c70 Zero crossing selection
58:22 \u2013 o-- Others58:37 \u2013 o01 Delay of outputs at startup
59:11 \u2013 o02 DI1 configuration
1:01:36 \u2013 o05 Password
1:02:08 \u2013 o06 Sensor type selection
1:02:27 \u2013 015 Display resolution
1:03:31 \u2013 o23 Relay 1 counter, o24 Relay 2 counter, and 025 o24 Relay 3 counter
1:04:13 \u2013 o37 DI2 configuration
1:04:52 \u2013 o61 DI2 configuration
1:05:07 \u2013 o67 Save settings as factory
1:05:39 \u2013 o71 DO2 config
1:06:23 \u2013 o91 Display at defrost
1:07:04 \u2013 P-- Polarity1:07:06 \u2013 P73 DI1 input polarity and P74 DI2 input polarity
1:07:32 \u2013 P75 Invert alarm relay
1:07:59 \u2013 P76 Keyboard lock enable
1:08:21 \u2013 u-- Readouts1:08:30 \u2013 u00 Controller Status
1:09:37 \u2013 u01 Air temperature (Sair)
1:10:12 \u2013 u58 Compressor relay status, u59 Fan relay status, u60 Defrost relay status, and u63 Light relay status
\xa0Find out more about the Danfoss ERC 213 HERE.
Learn more about Refrigeration Technologies at refrigtech.com.
If you have an iPhone, subscribe to the podcast HERE, and if you have an Android phone, subscribe HERE.